M Science Data Scientist
Interview Questions & Guide 2026

• Take a single feature change and write the full design: randomization unit, the exact point of exposure, the primary metric with its grain, guardrails, allocation, planned duration, and the decision rule committed before any data exists.
• Write why the randomization unit must sit at or above the level where treatment can spill over, and give one case where user-level randomization is still contaminated (shared accounts or devices, or two participants in the same marketplace).
• State in advance what you will do if the primary metric is flat while a secondary metric is significant.

Deliverable: A one-page test design with a decision rule written before launch.

• Compute required sample size per arm for a binary metric with the normal approximation, n is approximately 2 times (z for alpha/2 plus z for power) squared times p(1 minus p) divided by delta squared, for baselines of 2, 10 and 40 percent at a 5 percent relative lift, and note that for a fixed relative lift the requirement falls as the baseline rises because delta grows proportionally with p.
• Redo the calculation for a continuous metric using variance in place of p(1 minus p), and show why a heavy-tailed quantity such as revenue per user needs either far more traffic or a capped version with a stated cap.
• Convert one of the results into weeks given a weekly eligible traffic figure, then list the two honest ways to shorten it (accept a larger detectable effect, or reduce variance) and write why quietly lowering the power target is a decision to miss more real wins, not a speedup.

Deliverable: A small script or sheet that maps baseline, minimum detectable effect, alpha and power to sample size and weeks, cross-checked against a published calculator.

• Take a ratio metric whose denominator is not the randomization unit (clicks per session, randomized by user) and compute the standard error twice, once naively at session level and once by the delta method or a user-level bootstrap, then record how much the naive version understates it.
• Implement CUPED on simulated data: choose a pre-period covariate X measured before assignment, estimate theta as Cov(Y, X) divided by Var(X), and analyse Y minus theta times (X minus its mean) in place of Y. Confirm the variance of the adjusted outcome equals the raw variance multiplied by one minus the squared correlation between Y and X, so a correlation of 0.45 removes about 20 percent of the variance and not 80.
• Now run that simulation a few hundred times and confirm the adjusted effect estimate is unbiased for the same effect rather than numerically identical to the raw one. Within any single run the two differ, sometimes by a large fraction of the true effect, because the two arms' pre-period covariate means never coincide exactly in a finite sample; they agree in expectation, which is the property that matters and the one to state out loud.

Deliverable: A notebook showing the adjusted estimator with a measurably smaller variance than the raw one, plus a repeated-simulation table showing the two estimators agreeing on average while differing run by run.

• Run a sample ratio mismatch check as a chi-square goodness-of-fit test against the intended allocation, and write the three causes you would chase first (assignment logged before exposure, an arm-specific redirect or load failure, bot filtering applied asymmetrically).
• Simulate peeking: generate A/A data, test daily at alpha 0.05 across 14 looks, record the inflated false positive rate, then apply an alpha-spending boundary or commit to a fixed horizon and confirm the rate returns to nominal.
• Write how you would separate a novelty effect from a durable lift using the treatment effect plotted against days since first exposure, and what shape would change your recommendation.

Deliverable: One table showing the peeking false positive rate before and after correction, plus a written SRM triage list.

• Write the identifying assumption for difference-in-differences (parallel trends in the absence of treatment), then plot pre-period trends for two candidate control groups and justify rejecting one of them.
• Design a switchback test for a change where user-level randomization would leak across participants, choosing a time-block length against the carryover you expect and saying how you would detect carryover in the data.
• List what an interrupted time series or a synthetic control buys you and the one thing neither can rule out: an unobserved shock that coincides with the launch.

Deliverable: A one-page memo recommending a single quasi-experimental design and naming its weakest assumption explicitly.

• Write the assignment-to-exposure join that returns exactly one row per unit per experiment, and handle units appearing in both arms by excluding and counting them rather than silently keeping one.
• Compute the per-arm metric, its variance and the relative lift with a confidence interval in SQL, then reproduce the identical numbers in a notebook as a cross-check.
• Add a segment breakdown and write the sentence that keeps it from being p-hacking: segments declared in advance, everything else reported as exploratory and corrected for multiplicity.

Deliverable: A single query that outputs the full readout table, matched to a notebook recomputation.

• Give a 10-minute readout of a real or simulated experiment in the order decision, number, uncertainty, caveat.
• Have your listener ask "can we ship it" in the case where the primary is flat and a guardrail moved, and answer with a recommendation rather than a request for more data.
• Rewrite your opening line so the recommendation lands before any methodology.

Deliverable: A one-page readout whose first line is the recommendation.